GRBL Based UNO R3 with CNC Shield V3 and DRV8825 Stepper Driver Controller Bundle for Workbee Lead
[32869070209] GRBL Based UNO R3 with CNC Shield V3 Controller Bundle TheBulk Man 3D'GRBL Controller Bundle contains all the hardware for powering and controlling your WorkBee, Ox CNC or other CNC machine. - For Machine Size 500x750mm, 750x750mm, 750x1000mm, Please choose"GRBL-S" Version - For Machine Size 1000x1000mm, 1000x1500mm, 1500x1500mm, Please choose"GRBL-L" Version QTY Description 1 Arduino(Compatible) UNO R3 with USBCable 1 CNC shield v3.00 4 Stepper Driver – DRV8825 1 Fan – 40×40 24V 1 MEAN WELL Power Supply – 24V 350W 1 4 Core Shielded Cable (use for X Axis, Y Axis, Z Axis and A Axis with proper length for convenience) 1 2Core Shielded Cable (use for X Axis, Y Axis, Z Axis and A Axis with proper length for convenience) 1 DC Power Cable 1 Ground Wire 4 4 Pin Dupont Wire 3 2 Pin Dupont Wire 4 Terminal Block (4Pole) 3 Terminal Block (2 Pole) 1 E-Stop Switch +E-Stop Cable 3 Limit Switch Kits 4 Welding-free plug-in terminal block 10 Black Mini Jumpers Notice: 1. PDF Assembly Manual is available by email. 2. You need to log in GRBLofficial website to downloadthe software by yourself. (GRBL is free to download)Thank you for attention. More Details: Controller:The Controller comes is made up of the following items: Arduino UNO Compatible 14 digital input/output pins – 6 pins can be used as PWM outputs 6 analog inputs 16 MHz crystal oscillator Operates at 5V Recommended input voltage range: 7V to 12V Flash Memory: 32 KB (0.5KB used by bootloader) SRAM: 2KB EEPROM: 1KB CNC Shield V3 Version 3.00 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13) 2 x End stops for each axis (6 in total) Uses GRBLas control software Power supply: DC 12-36V Interface: mini-USB Maximum stepper motor current: less than 2A 2 phase 4 wire stepper motor Over 1A stepper motors must use heat-sinks and/or other cooling (fan) DRV8825 Stepper Drivers Low RDS (ON) outputs Automatic current decay mode detection / selection Internal UVLO Mixed with slow current decay modes Synchronous rectification for low power dissipation Crossover-current protection Thermal shutdown circuitry 3.3 and 5 V compatible logic supply Ground Fault Circuit Load short-circuit protection Sixmicrostepping modes: full, 1/2, 1/4, 1/8, 1/16 and 1/32 Fan – 40x40mm 24V Dimensions: 40mm (L) x 40mm (W) x 10mm (H) Rated Voltage: 24V Current: 0.10A Input Power: 0.84W Nominal Speed: 6000 RPM Air Flow: 5.75 CFM Noise: 24 dBA Wire Length: 250mm Connector: 2pin 2.54mm Power: MEAN WELL Power Supply – 24V 350W Output Voltage-Channel: 24 V Output Power: 350.4 W Enclosed Case Input Voltage: 90 VAC to 132 VAC/180 VAC to 264 VAC, 240 VDC to 370 VDC Output Current-Channel: 14.6 A Mounting Style: Chassis Length: 215 mm Width: 115 mm Height: 30 mm Input Frequency: 47 Hz to 63 Hz Unit Weight: 760 g Cables & Connectors: 4 Core Shielded Stepper Cablesterminated at one end with JST SM 4P (Connector to Stepper Motors) 2 Core Shielded Signal Cablesterminated at one end with JST SM 2P DC Power Cable 22 AWG 1 x 500mm Ground Wire 20 AWG 1 x 500mm Stepper Cables(CNC Shield to Connectors) Dupont Female Connector at one end 4 x 300mm EStop Cable 22 AWG 1 x 1000mm 4 x Terminal Block 5 Pole 3 x Terminal Block 3 Pole Signal: 3 x Limit Switch Kits 3 x Micro Limit Switch 3 x Limit Switch Plate 6 x M3 10mm Cap Head Screw 3 x M5 8mm Low Profile Screw 3 x M5 Drop-in Tee Nut NOTE:The holes in the switch will need to be opened a little (3mm drill bit) to allow for the M3 screw or alternatively you can use a M3 tap to cut a threadinto the plastic. 1 x E-Stop Switch Max Current: 10A Max Voltage: AC 660V. Rated Load: AC: 220VAC/6A, 380VAC/4A, 660VAC/2A DC: 440VDC/0.3A, 220VDC/0.5A, 110VDC/1A TYPE: N/C Withstand Voltage: 2500V /60S Temperature: -25°~+55° Contactresistance: <25mΩ Regarding our Shielded Cables: The 4 core and 2 core shielded cables bybulkman3dare cut in the proper length for customers convenience which meet the needs and multifunction of different size of our CNC Machine. This high quality 4 core cable has 2 layers of insulation and 2 shield layers to reduce signal interference and maximuse efficiency. The four insulated wires are shielded by oxygen free tinned annealed copper wire braid with Aluminium/PET tape (100% coverage) to shield the cores from EMF interference. This is again insulated by a thick clear layer of thermoplastic sheath insulation. Suitable for applications requiring electrical/electronic screening of cable. 22AWG suitable for 300V DC and up to 80°C Wiring Schematic: IMPORTANT NOTE: NEVERconnect or disconnections any wire while power is applied. ALWAYSdisconnect power before making any connections or disconnections. Failure to do the above will result in damage to the stepper drivers. Software: GRBL GBRL Controller Universal G-Code Sender Links: http://blog.protoneer.co.nz/arduino-cnc-shield/ Note :Any Mains power connections must be installed by a Licensed electrician or suitability qualified person. Top Selling CNC You May Like --------------------------------------------------------------Email:bella@bulkman3d.com-------------------------------------------- Payment We accept Alipay, West Union, TT. All major credit cards are accepted through secure payment processor ESCROW. Payment must be made within 3 days of order. If you can't checkout immediately after auction close, please wait for a few minutes and retry . Shipment Please write MUST MATCH Shipping order addresses. Item will be shipped within 1-3 business days in normal time. If you have not received your shipment within 30 days from payment(Brazil 60-100days), please contact us. We will track the shipment and get back to you as soon as possible with a reply. Customs Tax Import duties, taxes and charge are not included in the product price or shipping charge. Those charges are buyer's responsibility. We usually will mark the goods for a low cost on the customs declaration and we are trying to help you minimize or avoid GST or V.A.T or other import taxes. But we cannot guarantee no tax charge as it is depends on your country's policy. Feedback We will work with you to until you are satisfied. we sincerely hope that you can leave us aPositive Feedback& 5 Stars, for any reason you are not satisfied with your purchase, please contact us through (My Messages) or (Ask Seller Questions), Trade manager, before leaving neutral or negative feedback. We will do our best to resolve any problem and satisfy your needs.
US $98.00Get Now 5% US $93.10
Tidak ada komentar:
Posting Komentar